![chevrolet transmission casting numbers chevrolet transmission casting numbers](http://www.britishv8.org/Articles/Images-V15-2/T5-ID-Number-Tag.jpg)
56 Nomad, Ramjet 502, Viper 6-speed T56, C4 Corvette front and rear It was phased out of use and superceded by GM's 700R4 starting in 1982. The GM was not here but it is above the trans hole on the top part of the bellhousing centered between the upper trans retaining bolts. On this page you will be able to look up the original part numbers for 1958-1965 348 and 409 Chevy engine components such as Bell Housing, Carburetor, Camshaft, Crankshaft, Distributor, Generator/Alternators, Radiator Hoses and Starters. I have provided a partial list of this part number found in the parts catalogs. Bellhousings that will be used with a Toploader must measure 6 1/4" deep. Corvette, Camaro, Chevelle, Impala, Nova, etc There is a fine line between hobby and obsession and I think I crossed it! [This message has been edited by 75 400 4 Speed The bellhousings look fairly similar, but there are some key differences between the two. A quick search states it's for a '66-'79 Big Block Chevy. On non-world-class T5 transmissions it looks like a freeze plug, whereas on the later trannies it's a heavier steel cover (marked "Timken" and with a part number). Which bellhousing would I need to bolt up a T5 with a Chevy bolt pattern to a stude v8.
CHEVROLET TRANSMISSION CASTING NUMBERS DRIVER
if you are doing a restoration of an early muscle car, or just want the original 403 bellhousing to finish that rod project, this bellhousing is the perfect part! features: replaces gm part # 3858403 Casting Date Small block casting date is located on driver side rear of block on flange forward of bellhousing. Chevrolet Identification # 3729001 Clutch Housing. If you don’t need a steel bell housing this is a cost-saving option.
CHEVROLET TRANSMISSION CASTING NUMBERS MANUAL
Also, the bolt pattern on the rear of the bell housing is the same, thus, ANY Chevy 3sp, 4sp or aftermarket manual transmission will bolt up to a Chevy bell housing (or scatter shield). Bellhousing, Manual, GM NV 4500 Transmission to Chevy, Big/Small Block V8, V6, Each. 61 low ratio and reverse gear synchronization. This bellhousing is correct for 1964 Pontiac B bodies, with V-8 engine and standard transmission. The Turbo 350 is the shortest and one of the strongest automatics that can be put into a Jeep. Go here for info on Chevy Automatic Transmission Identification. Most often trucks have a 5 1/8" center register cars measure 4 66" "Cad Lasalle" Long input, bearing retainer not bolted to trans.
![chevrolet transmission casting numbers chevrolet transmission casting numbers](https://content.invisioncic.com/r277599/monthly_07_2013/post-32129-143141981235_thumb.jpg)
The 19 Chevy versions have a lower first gear of 6. 2 & 4 Door, Hardtop, Sedan, Convertible and Wagon. There are three common starter bolt patterns for the V8 or late six. 683) - so it's often refered to as a " 403 " Bellhousing (just 'Housing' to GM). The engine is built but not installed yet maybe 350 HP depending on whether I put some decent Chevrolet Truck Bellhousing Casting Number 460486 299. 221 V8 260 V8 289 V8 (made before August 3, 1964) - had five bolts holding bellhousing to block Later Small Block V8 pattern. These are the bolt holes found around the center of the flywheel. ), T5,700R4,200R tranny's came with the Bellhousings for 60* in these applications if that helps.